「山水工业门电机」先锋提升门电机的安装方法-工业快速门配件网

工业快速门配件网

公司承诺:
生产最好的快速门电机,做最好的快速门控制箱
全国服务热线:联系我们  
400-6080-090   
  • 联系电话:13940183063
  •   
  • 服务电话:400-6080-090
  •   
  • 联系人:于经理
  • 您现在的位置是   工业快速门配件网>>最新资讯 >> 「山水工业门电机」先锋提升门电机的安装方法

      「山水工业门电机」先锋提升门电机的安装方法

      作者:山水工业门电机批发   时间:2019/7/18 9:45:02

    • 「山水工业门电机」先锋提升门电机的安装方法


      Installation Method of Pioneer Hoist Door Motor of Shanshui Industry Door

       




      「山水工业门电机」安装之前,请检查门体的运行情况,应使门体运行平稳,无卡滞;平衡系统良好,能轻松用手推拉门运行。


      Before mountainous industry door motor is installed, please check the operation of the door body, so that the door body can run smoothly without jamming, and the balance system is good, so that the door can be easily operated by hand.


      电机的安装有轴驱式和链驱式,我公司配置单额附件为轴驱式。用户采用链驱式安装,可自行更具需要选择相应的链轮链条及安装方式进行安装和调试。


      The motor is equipped with shaft drive type and chain drive type. Our company configures single accessories as shaft drive type. Users can install and debug sprockets and chains by using chain-driven installation mode, which makes it more necessary for them to choose the appropriate sprockets and chains and installation mode.


      轴驱式安装方式方便简洁,即把提升门电机直接安装在门轴上,只要门框一侧有250mm左右的空间就能进行电机的安装。


      Axle-driven installation method is simple and convenient, that is, the lifting door motor is directly installed on the door axle, as long as the door frame side has about 250mm space to install the motor.


      具体步骤如下:


      The specific steps are as follows:


      1、选取合适的「先锋工业门电机」安装位置,划好线,并根据划线位置在墙体上钻好安装板用膨胀螺钉孔。


      1. Choose the suitable installation position of "Pioneer Industrial Door Motor", draw the line, and drill the expansion screw hole for the installation board on the wall according to the location of the line.


      2、在门轴上先套入一个固定套,然后把主机套入门轴上。用M10螺栓将机器紧固定在安装板上(安装板在机器的左右侧皆可以)


      2. Insert a fixed sleeve on the door axle first, and then put the main frame sleeve on the entry axle. Fix the machine tightly on the installation board with M10 bolt (the installation board is available on both sides of the machine)


      3、调好位置,注意应使机器上的手动链条垂直于地面(机器水平、竖直均可),用膨胀路额定把安装板紧固定在钻好孔的墙上,并上紧四个M10螺丝。


      3. Adjust the position, pay attention to make the manual chain on the machine perpendicular to the ground (horizontal and vertical machine), fix the installation plate on the wall of the drilled hole with the rated expansion path, and tighten four M10 screws.


      4、拉动红色拉手到手动工作位置,,并轻拉手动链条使门轴上的键槽和主机上的键槽对齐,插入6*80的平键,然后把第二个固定套嵌入门轴中,并使左右两侧的固定套靠近机器轴端面,并上紧止头螺钉,以防止机器和平键掉落出现以外。


      4. Pull the red handle to the manual working position, and gently pull the manual chain to align the keyway on the door axle with the keyway on the main engine, insert the 6*80 flat key, then insert the second fixed sleeve into the door axle, and make the left and right fixed sleeves close to the end face of the machine axle, and tighten the stop screw to prevent the machine and the flat key from falling out. Now outside.


      关于「山水工业门电机」的安装方式就是这些了,如您需要采购山水提升门电机,先锋工业门电机,我们可提供多种型号,如GK60S/GK40/GK90S/GK50/70等。


      This is the way to install "Shanshui Industrial Door Motor". If you need to purchase Shanshui Lifting Door Motor and Pioneer Industrial Door Motor, we can provide a variety of models, such as GK60S/GK40/GK90S/GK50/70.

       

    无锡西塘环件有限公司 济南至晟制冷设备有限公司 贴标机 浙江铭锋阀门有限公司 济南启力仓储设备有限公司 邢台市丰兴机械制造有限公司 炭黑 江苏双诚分析仪器有限公司 河北安邦安防设施有限公司 河北启程路桥养护工程有限公司